Please call our toll free number to discuss ordering. 7:30 am - 10:00 pm CST Mon-Fri 8:00 am - 8:00 pm CST Sat-SunIt's possible, what you're going to want to do is water-log the wood so that it sinks. If it's a small piece, you can drastically shorten the time it takes to water-log it by boiling it constantly for one to three days depending on how hard the wood is. Once the wood is waterlogged enough to sink in water it's ready. Boiling it also helps to rid the wood of any bacteria and/or parasites that might be on it. If the wood is too big to fit in a pot, you'll need a container that's big enough to hold the wood submerged in hot water. Unless you're able to keep the water at a boiling temperature, this process is going to be much slower, lasting several months (The natural process of water-logging wood takes about four to six months). Submerge the wood in boiling water and let it sit. Every other day you're going to want to perform water changes, taking some of the old water out, and replacing it with clean, boiling water.

As the wood sits in the water, it will release what is called tannins. The tannins won't harm anything, but it does make the water cloudy, so it's best to get rid of it as much as possible before you put it in your fish tank. Depending on how you want your wood to look, after a week or so you should be able to start working the bark off. Taking off the bark should speed up the process a bit. If you want to keep the bark on, you'll still want to take a hard brush and scrub the bark to get as mush of the loose parts and dirt off as you can. Keep doing the process of changing the water every other day, and scrubbing the bark once a week, for about two or three months. By that time the water should have seeped into the wood enough to make it sink. If it hasn't you can continue, or weigh it down in your fish tank if you want, by then there shouldn't be much more for tannins leaching into the water. I prefer to avoid picking wood that's been in the water already. While it will give you a head start, you also have to make sure you don't bring along any hitchhikers (snails, leeches, small invertebrates).

While it takes longer to water-log wood from dry land, simply submerging the wood in hot water should get rid of any hitchhikers there. If the wood you find is small enough to fit in a pot to boil it, then it shouldn't be a worry. Some people suggest adding a tiny bit of bleach to kill the bacteria and hitchhikers when you can't boil the wood. The problem I have with this, is if you don't successfully get rid of the bleach it could seriously harm your fish, which is why I don't suggest it personally.fish tank filter price india I've heard using saltwater helps (saltwater as in ocean water, not adding table salt), but I haven't tried it myself.fish tank models and price in chennai If I was able to at the time, I would have dropped a aquarium heater into the bucket to keep the water constantly warm. fish tank second hand sale

A broken heater that would keep the water boiling would be nice too. To get the bleached driftwood look. You'll have to take off the bark, then bake it under a heat lamp for a couple months before water-logging it.If you wish to add a natural elements such as driftwood to your aquarium, you need to spend some time preparing the wood and considering how to best out its best aesthetic qualities. Driftwood and other natural structures such as complimentary rocks and stones  may make up a large portion of your aquarium. fish aquariums online shoppingOnce you aquascaped driftwood into your aquarium and added some fish, adjustments become difficult and can cause significant stress. fish tank for a bettaSometimes a lack of forethought may end up in taking apart the entire aquarium and starting all over.  o lar das crianças peculiares dublado online

My motto is: Do it right the first time. With a bit of planning, you can have a beautifully aquascaped aquarium with minimal effort and no disturbance at all. Before placing the driftwood in your aquarium, draw a rough sketch of your aquarium and where you want to locate the driftwood. Consider how your aquarium will look with the driftwood positioned vertically as opposed to the conventional horizontal position. Read the article on Hardscaping, which you will find under the Aquascaping drop-down menu. It contains a lot of useful information about composition and prepanning you aquascape. There, as here I emphasise: Do not be is such a hurry to begin working in your aquarium. First construct your scape on a table,  using a cardboard cutouts to represent your aquarium tank floor and back wall. This is more hands-on than drawing your layout. It also allows you to experiment with different ideas and certainly helps you to better visualize your aquascape without the frustration and stress the same experiment would cost you if you worked directly in the tank.

Additionally, it allows you to get everything together, tie or glue those pieces you want to become the main element, and securing weights at the bottom of those pieces that might float up — so that once you finalised your design, you are completely prepared. Driftwood needs to be cleaned before placement. Use a clean brush to scrub the driftwood thoroughly to remove any dirt or debris. Do not use soap or any chemical cleansers. Any residue from these products could poison your aquarium. The cleaned driftwood will then need to be soaked to saturate and “cure.” Though most driftwood will remain submerged underwater, some driftwood remains slightly buoyant until it is fully saturated and “waterlogged.” Soak the driftwood in a large bucket as long as possible, making sure the entire piece is completely underwater. A minimum period of 1 to 2 weeks is recommended to allow total saturation. Soaking also allows excess tannins that can darken and discolour the water to leach out.

The discoloration caused by the tannins will not harm your aquarium inhabitants, but it will lower the pH slightly over time. Some hobbyists take advantage of this feature and utilize the tannins to achieve soft water conditions preferred by many tropical fish. Monitor the soaking driftwood regularly to see if the water needs to be changed. As the water darkens, empty all of the water and gently rinse the driftwood. Fill the bucket with clean dechlorinated or reverse osmosis (RO) water and continue soaking the driftwood. As you repeat this process, you will notice that the water will appear to cause les ‘tea-staining’. When you no longer notice any significant discolouration for several days in a row, the driftwood is ready for placement. Boiling driftwood has several benefits. Just like steeping a tea bag in hot water, boiling driftwood in a large stockpot will encourage more tannins to leach out faster, thereby considerably shortening the curing process. More importantly, boiling sterilizes the driftwood, killing algal or fungal spores that can take hold once introduced into the aquarium with the driftwood.