What Is Aquarium Salt Creep?Salt creep occurs when the water in an aquarium that contains salt splashes out of the tank, gets things wet, and after the fresh portion of the water evaporates, all that is left behind are salt crystals.What Are The Effects of Salt Creep?Salt is a corrosive substance, and therefore it can affect anything it touches. What degree of damage occurs primarily depends on how long an item is exposed to sodium chloride, and based on what type of material it comes in contact with, its effects are seen in varies ways. Glass, acrylic and plastic becomes "etched". Where the saltwater settles and dries, residual white water spots develop, and glass in particular takes on a foggy appearance.Electrical items corrode, especially metal parts of light fixtures, equipment power plugs and the outlets they are connected into.Unprotected bulbs become encrusted with a layer of salt, which blocks light from getting into the aquarium.Protective glass and acrylic light covers or canopies become encrusted, as well as etched, resulting in a reduction of light into the aquarium.

Wood, cement, plaster board or drywall, drapes or curtains, carpet and flooring materials slowly erode away, and paint peels off.How To Deal With Salt CreepThe longer salt is allowed to sit and build up, the more damaging it can be. To lessen and slow down the effects of salt creep, the best way to deal with it is to regularly keep it cleaned up, and take steps to prevent unnecessary damage to anything near the aquarium. Here's how:Keep the tank, hood, stand, light fixture and other such items clean by wiping them down with a cotton rag or wash cloth rinsed in freshwater. aquarium fish online in indiaFor unsightly white water spots that can develop on plastic items that are outside of the aquarium, a touch of vinegar applied to the cloth may help to reduce their appearance.aquarium fish online australia

Remove and rinse off pieces of equipment that can be cleaned in freshwater, this includes equipment that has an electric motor. If a electrical device has been exposed to (i.e. immersed in) saltwater, you are far better off to rinse it thoroughly in freshwater (not when it is plugged into a power source), then dry it, than you are to let the corrosive effects of the salt take its toll on the equipment over time.Position electrical equipment out of range of splash zones.fish tank vacuum pythonUnplug and wipe down electrical equipment power cords, plugs, and outlets.aqua one aquarium filtersProtect nearby walls by attaching a sheet of clear acrylic to act as a splash board.aqua one aquarium digital internal thermometer

Place towels on the floor around the bottom of the aquarium during maintenance procedures.Keep the water level up to or just above the tank's trim line to help reduce etching of the aquarium material.Avoid using bubble wands or air stones, as these only contribute to an increase of salt creep problems.Direct the flow of outlets that return water to the aquarium, as well as equipment that is used to move water inside the aquarium in a way that reduces excess splashing.glass fish tank designMany aquarium cabinets and stands are open in the back. If you have a sump under your tank, saltwater will splash not only inside the cabinet, but out the back and onto a wall or the floor. It may only be a drop or two (hardly noticeable) at a time, but over time it adds up. Placing a thin sheet of acrylic over the opening in the back of the cabinet will keep the drops of saltwater from escaping the cabinet and damaging the floor and wall behind the tank.

Paint any unpainted wood surfaces (aquarium cabinets and stands) with a good quality enamel paint. This makes the wood surface easy to keep clean and salt free with the wipe of a damp cloth and keeps the salt from soaking into the wood where it will be next to impossible to get rid of.6" clear acrylic piano hinge- How - To Use Clear Acrylic Piano Hinge 1-3/4" x 6". All sides beveled for a smooth appearance. May be cut to required length. Can be glued with silicon to glass. Don't buy an overpriced aquarium lid!  They are made for fish, so they are not built to keep Dart Frogs in!  Buy two pieces of glass from your local glass dealer, get a hinge, a knob or pull, and either a hasp or a door catch. Check out our blog on how to use acrylic parts HERE! Shipping is based on distance and weight of total order.  To get a shipping quote for your order, add the items to your cart and click on "shipping estimator" in your cart. Not satisfied with your purchase? 

Simply return it to us and we'll offer a full refund.  Shipping and return shipping are not covered. Read What Others Are Saying: Eyad From Dubai - UAE Review by Really Good Products , You Give me the right solution to my DIY vivariumsLog in or Sign up 564 posts, read 1,432,036 times 5,128 posts, read 10,818,672 times Hex hoods are not commonly found... Originally Posted by bgmv90 I have never seen hoods for hex tanks, and I've kept tanks for a long time. You have many options though. Try calling the vendor (Marineland, Oceanic, etc.) They should be able to point you to a dealer, or sell you one directly. Another option, and cheaper, would be to seek out the fresh, or salwater clubs in your area, register, and post a WANTED add in their forum. You might get someone to give you one for free. The next thing you can try is to find a plastics retailer in your area, ask them to cut a lid for you out of acrylic, it should not be expensive. Alternatively, if you know someone who has woodworking tools, you can buy scrap acrylic and have that person cut a lid for you.